G. Atmeh, F. Darwish, and Z. Hasan
Jordan University of Science and Technology, Irbid, Jordan
Texas A&M University, College Station, TX, USA
The present study focuses on the design and analysis of a single-engine, propeller-driven general aviation airplane. Initial weight estimation based on the initial sketch and the design mission profile is conducted. The estimated weight and other design parameters are used to define the external geometry of the fuselage, wing and tail. Conic lofting is utilized to render a layout of the design ...
E. Rawashdeh, A. Arevalo, D. Castro, I. G. Foulds, N. Dechev
Computer, Electrical & Mathematical Sciences & Engineering Division (CEMSE), King Abdullah University of Science & Technology, Thuwal, Saudi Arabia
School of Engineering, Okanagan Campus, The University of BC, Vancouver, BC, Canada
University of Victoria, Victoria, BC, Canada
In this work we present the simulation of a micro-scale large displacement compliant mechanism called the Tsang suspension. It consists of a flat micro-plate anchored down by two springs on either side, that can rotate out-of-plane and maintain its vertical assembly by a simple single-axis actuation. COMSOL Mutliphysics® software was used to simulate these devices and extract the reaction forces ...
Y.F. Wang, Y.S. Wang, L. Wang
Institute of Engineering Mechanics, Beijing Jiaotong University, Beijing, China
Department of Mechanical Engineering, Østfold University College, Halden, Norway
We show in this paper that by careful design of the geometry of the resonators, complete bandgap with relatively low center frequency can be obtained for 2D and 3D Phononic Crystals with resonators. The generation of the bandgap is due to the local resonance of the unit cell. Spring-mass and spring-pendulum models are developed to predict the boundaries of the complete bandgap. The predicted ...
M. Curatolo , L. Teresi ,
 Department of Engineering, Università Roma Tre, Roma, Italy
 Department of Mathematics and Physics, Università Roma Tre, Roma, Italy
Our goal is to reproduce the key features of carangiform swimming by running 2D simulations which fully exploit the Fluid-Structure Interaction interface of COMSOL Multiphysics software. Fish swimming is an important area of research, with relevant developments on biomechanics, robotics and mathematical modeling. Usually, in fish swimming simulations, the motion of the fish is assigned, and much ...
D. van den Ende
Holst Centre / TNO, Eindhoven, The Netherlands
Ultra-thin chips of less than 20µm become flexible, allowing integration of silicon IC technology with highly flexible electronics. This combination allows for highly intelligent products of unprecedented thinness, flexibility and cost. Examples include sensor systems integrated into food packaging or healthcare and sport monitoring tags as wearable patches or even directly in clothing textile ...
K. C. Koppenhoefer, J. Thomas, J. S. Crompton
AltaSim Technologies, LLC., Columbus, OH, USA
Computational tools based on the finite element method have been used extensively to develop solutions for elastic and elastic-plastic fracture mechanics problems. This work uses a small-scale yielding model to compare results developed from COMSOL Multiphysics® with another finite element modeling package and analytical solutions. Analysis are conducted for elastic, and elastic-plastic ...
Lamb Waves and Dispersion Curves in Plates and It’s Applications in NDE Experiences Using Comsol Multiphysics
P. Gómez, J. P. Fernandez, and P. D. García
Hydro-Geophysics & NDE Modeling Unit
University of Oviedo
In this paper, a model for numerically obtaining lamb wave modes and dispersion curves in plates is presented. It is shown that COMSOL Multiphysics can be employed to simulate the behavior of guided waves in dispersive plates, which is useful for NDE applications. A two dimensional steel plate (4x0.1 meters) is excited with a space-time impact point source. To model the point source, we use ...
N. Elabbasi, J. Bergstrom, and S. Brown
Veryst Engineering, LLC.
Peristaltic pumping is an inherently nonlinear multiphysics problem where the deformation of the tube and the pumped fluid are strongly coupled. We used COMSOL Multiphysics to investigate the performance of a 180 degree rotary peristaltic pump with two metallic rollers, and an elastomeric tube pumping a viscous Newtonian fluid. The model captures the peristaltic flow, the flow fluctuations ...
E. Varadarajan, M. Bhanusri,
Research and Innovation Centre (RIC), IITM Research Park, Chennai, Tamil Nadu, India
Department of Physics, Indian Institute of Technology (IIT) Madras, Chennai, Tamil Nadu, India
In this paper we made an attempt to maximize the power output in the different piezoelectric materials in a unimorph cantilever beam configuration. In this research, a macro scale unimorph piezoelectric power generator prototypes consists of an active piezoelectric layer, stainless steel substrate and titanium proof mass was designed for frequencies 60 Hz - 200 Hz. An analytical model of a micro ...
P. Hanasi , B. G. Sheeparamatti , V. Abbigeri , N. Meti ,
 Visvesvaraya Technological University, Belagavi, Karnataka, India
Capacitor is mainly defined as two conducting plates that can hold the opposite charges on it. These plates can be used either as a sensor or an actuator. If the relative distance between the two conductors changes as result of given input, then capacitance values will change. This results in basic of capacitive or electrostatic sensing configuration. On the other hand, if a voltage or the ...