A. Bahrami, D. K. Aidun
MAE Department, Clarkson University, Potsdam, NY, USA
COMSOL Multiphysics® is used to simulate the transport phenomena in arc welding of Nickel to 304SS. Electric Currents (ec) and Magnetic Fields (mf) are used to solve for the Lorentz force which is one of the volume forces. Laminar Flow (spf) is used to simulate flow field. The Lorentz and buoyancy forces are applied as volume forces to the fluid domain. Marangoni effect also is applied to the ...
E. Varadarajan, M. Bhanusri,
Research and Innovation Centre (RIC), IITM Research Park, Chennai, Tamil Nadu, India
Department of Physics, Indian Institute of Technology (IIT) Madras, Chennai, Tamil Nadu, India
In this paper we made an attempt to maximize the power output in the different piezoelectric materials in a unimorph cantilever beam configuration. In this research, a macro scale unimorph piezoelectric power generator prototypes consists of an active piezoelectric layer, stainless steel substrate and titanium proof mass was designed for frequencies 60 Hz - 200 Hz. An analytical model of a micro ...
Northwestern University, Evanston, IL, USA
Dye sensitized solar cells (DSSCs) have received tremendous attention as alternative photon harvesting devices. While the sintered TiO2 nanoparticle network attached with dye molecules achieves efficient photon absorption, the electrons have to diffuse through the long TiO2 network to reach the contact, resulting in a high electron density and thus increased recombination. Extensive research ...
Mitsubishi Turbocharger & Engine Europe, Almere, The Netherlands
This study presents a rotordynamic analysis of a rotor on hydrodynamic bearings using COMSOL Multiphysics®. In this paper, the complexity of the model is gradually increased. Starting point of the analysis is the modal analysis of the rotor in free-free conditions. A Reynolds model is set up to predict the film pressure distribution under shaft loading. Due to the cross coupling terms of the ...
H. Kwon, and E. Akyiano
Dept. of Engineering and Computer Science
Berrien Springs, MI
In this paper, the cyclic voltammetry behavior of Ferrocyanide/Ferricyanide, which is commonly used for electrochemical DNA detection experiment, was studied in the commercial EQCM-D setup (Q-sense) using the COMSOL Multiphysics. The model was established in a 3D geometry of QCM liquid cell. The simulation shows depletion of concentration of ferrocyanice following applied electrode potential. ...
K. Al-Shurman, H. Naseem
The Institute for Nanoscience & Engineering, University of Arkansas, Fayetteville, AR, USA
Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, USA
Chemical vapor deposition is considered a promising method for synthesis of graphene films on different types of substrate utilizing transition metals such as Ni. However, synthesizing a single-layer graphene and controlling the quality of the graphene CVD film on Ni are very challenging due to the multiplicity of the CVD growth conditions. COMSOL Multiphysics® software is used to investigate ...
S. Gorelick, M. Leivo, U. Kantojärvi
VTT Technical Research Centre of Finland, Espoo, Finland
Excessive air damping can be detrimental to the performance of oscillating MEMS components. Complex systems, such as structures in pre-etched cavities or angular comb-drive scanning mirrors, typically require simulations to reliably evaluate the air damping. The simulated and experimental performance of the following systems was evaluated and compared: two types of out-of-plane cantilevers, ...
J. Crompton, S. Yushanov, L. Gritter, and K. Koppenhoefer
AltaSim Technologies, LLC.
Thermoelectric phenomena provide the direct conversion of heat into electricity or electricity into heat, the phenomena is described by three related mechanisms: the Seebeck, Peltier and Thomson effects. Thermoelectric devices have found many applications ranging from temperature measurement, solid state heating or cooling and direct energy conversion from waste heat. In this paper, analysis ...
Heat Transfer and Phase Transformation on Matrix Assisted Pulsed Laser Evaporation (MAPLE) of Biocompatible Thin Layers
E. Lacatus, G.C. Alecu, M.A. Sopronyi, A. Tudor
POLITEHNICA University of Bucharest, Bucharest, Romania
INFLPR -National Institute for Laser Plasma and Radiation Physics, Bucharest, Romania
Matrix Assisted Pulsed Laser Evaporation (MAPLE) technique is used for the deposition of high quality biocompatible polymer thin films. During the deposition process the temperature of the laser target should be kept below 193K to assure the proper quality of both evaporation and deposition phases of the process. On a first approach COMSOL Multiphysics® was used to describe and analyze the ...
L. P. Aoki, H. E. Schulz, M. G. Maunsell
University of São Paulo, São Carlos, SP, Brazil
This article considers a closed water circuit with square cross section filled with an electrolyte fluid. The conductor fluid was moved using an electromagnetic pump, in which a permanent magnet generates a magnetic field and electrodes generate the electric field in the flow. Thus, the movement is a consequence of the magnetohydrodynamic (or MHD) effect. The model adopted here was derived from ...