Galeria de Modelos

A Galeria de Modelos possui arquivos do COMSOL Multiphysics de várias áreas de aplicação incluindo elétrica, mecânica, escoamento e química. Você pode baixar modelos prontos e também tutoriais passo-a-passo para montar seu modelo, e usá-lo como ponto de partida para o seu próprio modelo. Use a função de busca "Quick Search" para encontrar modelos na sua área de interesse e faça o login ou o seu cadastro no COMSOL Access, cadastrando a sua licença do COMSOL, para poder baixar os arquivos.

Fatigue Analysis of a Car Wheel Rim

A fatigue analysis is performed on a wheel rim. The Findley fatigue criterion is examined. The submodeling technique is utilized performed a detailed study on the critical part of a spike. At first a study of the full model is made. The critical part is identified and a submodel is reanalyzed. The road load, which rotates around the wheel, is mapped from the analysis of the full model to the ...

Structural and Fatigue Analyses of a Shaft with a Fillet

This benchmark model shows how to perform a high-cycle fatigue analysis for non-proportional loading using critical plane methods.

Cycle Counting in Fatigue Analysis - Benchmark

A benchmark model of the Rainflow counting algorithm compares results between ASTM and COMSOL fatigue module using a flat tensile test specimen. An extension is made for the cumulative damage calculation following the Palmgren-Miner model and results are compared with analytical expressions.

High-Cycle Fatigue Analysis of a Cylindrical Test Specimen

A benchmark model for the fatigue module. A cylindrical test is subjected to non-proportional loading. Three stress based models: Findley, Matake, Normal stress, are compared to analytical values and to each other. The non-smooth behavior of the Matake model is captured and discussed.

Low-Cycle Fatigue Analysis of Cylinder with a Hole

A load carrying component of a structure is subjected to multi-axial cyclic loading during which localized yielding of the material occurs. In this model you perform a low cycle fatigue analysis of the part based on the Smith-Watson-Topper (SWT) model. Due to localized yielding, you can use two methods to obtain the stress and strain distributions for the fatigue evaluation. The first method is a ...

Thermal Fatigue of a Surface Mount Resistor

A surface mount resistor is subjected to thermal cycling. The difference in the thermal expansion of different materials will introduce stresses in the structure. The solder which connects the resistor with the printed circuit board is seen as the weakest link in the assembly. It responds nonlinearly to changes in both temperature and time. In order to ensure the structural integrity of the ...

Random Load Fatigue in a Frame with a Cutout

A frame with a central cutout is subjected to a random load consisting of 1000 load events. The external load, recorded using three strain gauges, is simulated using superposition of three unit loads. The stress state around the cutout is obtained with the Rainflow cycle counting algorithm. The damage is estimated using the Palmgren-Miner linear damage rule.

Notch Approximation to Low Cycle Fatigue Analyis of Cylinder with a Hole

A load carrying component of a structure is subjected to multi-axial cyclic loading during which localized yielding of the material occurs. In this model you perform a low cycle fatigue analysis of the part based on the Smith-Watson-Topper (SWT) model. Due to localized yielding, you can use two methods to obtain the stress and strain distributions for the fatigue evaluation. The first method ...

High-cycle fatigue of a reciprocating piston engine

In a reciprocating piston engine the connecting rods transfer rotating motion into reciprocating motion. The connecting rods are constantly under high stresses and the load increases with the engine speed. A failure of one part in the engine usually results in a replacement of the whole engine. It is therefore of crucial importance to design all engine parts so that none of them will fail during ...

Bracket - Fatigue Evaluation

The S-N curve, also called the Wöhler curve, is one of the most popular methods for fatigue evaluation. The curve relates stress amplitude to the limiting fatigue life and can be obtained directly from a set of standard fatigue test. Many times our applications are subjected to conditions different from the experimental conditions of the fatigue tests. The fatigue data must then be appropriately ...

Quick Search

1 - 10 of 12 First | < Previous | Next > | Last