N. Elabbasi, X. Liu, S. Brown, M. Vidal, M. Pappalardo
Veryst Engineering LLC, Needham, MA, USA
Nordson EFD, East Providence, RI, USA
Laminar flow static mixers are accurate, inexpensive fluid mixing devices that can handle a wide range of fluids and mixing proportions. They have a wide range of industrial applications, especially in the consumer product, pharmaceutical, biomedical, and petrochemical industries. A good mixing quality is obtained when the outlet of the mixer has no concentrated volumes of either mixed materials ...
Analysis and Design of Antennas for an Implantable Medical Device System for Functional Electrical Stimulation
Alfred Mann Foundation for Scientific Research, Valencia, CA, USA
This poster outlines the results of finite element analyses to study the antenna radiation pattern of an implanted medical device. Also presented are simulation results used to design an electrically small antenna for a portable control unit that communicates with the implants over the Medical Micropower Network Frequency Range [413 MHz to 457 MHz]. Alfred Mann Foundation’s Functional ...
Pulsed Eddy Current Probe Development to Detect Inner Layer Cracks Near Ferrous Fasteners Using COMSOL Modeling Software
V. Babbar, P. Whalen, T. Krause
Department of Physics, Royal Military College of Canada, Kingston, ON, Canada
Surface breaking cracks in conductive structures can be detected by conventional eddy current techniques. However, it is very difficult to detect inner layer defects in multilayered conductive structures either by conventional eddy current or ultrasonic methods. The transient/pulsed eddy current (PEC) technology can potentially overcome these limitations and is being developed for detection of ...
I. Terechkine, T. Khabiboulline, D. Sergatskov
Fermi National Accelerator Laboratory, Batavia, IL, USA
Performance degradation of a superconducting RF cavity after quenching in an external magnetic field was calculated using COMSOL. This degradation is due to the increased resistance of a superconducting surface with trapped magnetic flux. The amount of the trapped flux depends on the size of the normally-conducting opening that develops in the superconducting wall of a cavity during quenching. ...
P.K. Jain, V.B. Khane, J.D. Freels
Oak Ridge National Laboratory, Oak Ridge, TN, USA
Missouri University of Science and Technology, Rolla, MO, USA
Simulation models for steady state thermal hydraulics analyses of ORNL’s HFIR have been developed using COMSOL. A single fuel plate and coolant channel of each type of HFIR fuel element was modeled in three dimensions. The standard k-? turbulence model was used in simulating turbulent flow with conjugate heat transfer. The COMSOL models were developed to be fully parameterized to allow ...
Simulation of Acoustic Energy Harvesting Using Piezoelectric Plates in a Quarter-Wavelength Straight-Tube Resonator
B. Li, J.H. You
Southern Methodist University, Dallas, TX, USA
An acoustic energy harvesting mechanism at low frequency (~200 Hz) using lead zirconate titanate (PZT) piezoelectric cantilever plates placed inside a quarter-wavelength straight-tube resonator has been studied using COMSOL Multiphysics 4.3 and compared with experimental data. When the tube resonator is excited by an incident wave at its acoustic eigenfrequency, an amplified acoustic resonant ...
H.P. Schmidt , U. Vogl
UAS HAW Amberg-Weiden, Amberg, Germany
For the design of an inductive power and data transfer electromagnetic calculation are carried out. A transfer system is considered for loads that are distributed across some distances. For example, such loads are adjustable speed drives that are found in factory automation and intra-logistic. Physical properties of the inductive transfer are modeled via COMSOL. Lumped parameters are deduced from ...
Modeling and Experimental Verification of the Power Transfer and Thermal Characteristics of Piezoelectric Transformers Subjected to Combined Mechanical and Electrical Loading
S. Tuncdemir, W.M. Bradley
Solid State Ceramics, Williamsport, PA, USA
QorTek, Williamsport, PA, USA
A piezoelectric transformer allows purely mechanical transfer and scaling of electrical energy via simultaneous utilization of both the direct and converse piezoelectric effects. This mechanical energy transfer enables a wide range of functional differences from typical magnetic-based electrical power transformers. Comparing to their electromagnetic counterparts, piezoelectric transformers are ...
X. Guan, E. Gratz, U. Pal
Division of Materials Science and Engineering, Boston University, Brookline, MA, USA
Computational fluid dynamics (CFD) modeling is a useful tool to gain an insight into various high temperature metallurgical processes such as the magnesium refining and the magnesium solid oxide membrane (SOM) electrolysis. In both processes, argon gas was used to stir the molten salt (flux) in order to improve the transport of magnesium vapor out of the flux and achieve chemical homogeneity in ...
J. Crompton, S. Yushanov, L.T. Gritter, K.C. Koppenhoefer
AltaSim Technologies, Columbus, OH, USA
The resonance conditions for surface plasmons are influenced by the type and amount of material on a surface. Full insight into surface plasmon resonance requires quantum mechanics considerations. However, it can be also described in terms of classical electromagnetic theory by considering electromagnetic wave reflection, transmission, and absorption for the multi-layer medium. The two commonly ...