## Non-Newtonian Fluids, Between Solids and Fluids

##### Valerio Marra | January 22, 2013

One of my favorite sitcoms is “The Big Bang Theory”, thanks to its focus on physics. From time to time they run funny experiments that can be easily arranged at home, causing me to wonder if I know the physics that are at work. One of my favorite episodes is when they fill the cone of a speaker with a suspension of starch in water. Instead of spattering around, the suspension starts to dance because it behaves more like a solid than a fluid under the percussive action of the speaker’s cone. Non-Newtonian fluids are another fascinating counter-intuitive effect to study.

### Materials Between Solids and Fluids

Solids deform under an applied stress and reach a position of equilibrium in which their deformation ceases. When the stress is removed, they will go back to their original shape. On the contrary, fluids deform continuously and don’t retain any particular shape. In scientific terms, we say that solids are characterized by *elasticity* while fluids are characterized by *viscosity*.

In between these two extremes lie *non-Newtonian fluids*, exhibiting both elasticity and viscosity. A suspension of starch in water belongs to this broad class of fluids and can be further classified as shear thickening: its viscosity increases with increasing shear rate. Another example of *shear thickening* fluid is sand soaked in water. The material dancing on a speaker’s cone on the TV show must therefore have been a non-Newtonian fluid.

### Have you ever painted?

If the answer is yes, I’m pretty sure you noticed that the shear created by the brush made the paint thin and capable of wetting out the wall surface evenly. Once applied, the paint regained its original higher viscosity, leaving your wall without drips and runs. This is what is called a *shear thinning* fluid, the exact opposite of shear thickening. Can you recall other fluids exhibiting a non-Newtonian behavior?

### Simulating Non-Newtonian Fluids

When looking to simulate non-Newtonian fluids, one example that comes to mind is the injection molding of a polymer. A ready-to-run model is available to download from the Model Gallery. I suggest starting from this model if you’re interested in simulating non-Newtonian flows. Below are a few images highlighting the shear thinning behavior of this polystyrene solution flowing into a mold.

*In this model the polystyrene solution is flowing into the mold from the top to
the bottom. Results show how for a shear thinning fluid, the dynamic viscosity is
lower when the shear rate is higher. Top: velocity magnitude. Bottom left: shear rate.
Bottom right: dynamic viscosity.*

*Dynamic viscosity as a function of shear rate. Values are measured in p1.*

*Top left: shear rate as a function of inlet pressure. Top right: dynamics viscosity as a
function of inlet pressure. Values are measured in p1. Bottom: comparison between the
non-Newtonian polystyrene solution and an equivalent Newtonian fluid. As expected, the
volumetric flow rate is higher for the polystyrene solution since at higher shear rates its
viscosity is lower.*

- Certified Consultants 23
- Chemical 32
- COMSOL Now 120
- Conference 98
- Core Functionality 41
- Electrical 68
- AC/DC 12
- MEMS 11
- Plasma 2
- RF 20
- Semiconductor 1
- Wave Optics 6

- Fluid 56
- CFD 21
- Microfluidics 6
- Mixer 2
- Molecular Flow 6
- Pipe Flow 4
- Subsurface Flow 6

- Interfacing 24
- Mechanical 88
- Acoustics 16
- Fatigue 4
- Geomechanics 1
- Heat Transfer 44
- Multibody Dynamics 4
- Structural Mechanics 31

- Multipurpose 10
- Tips & Tricks 29
- Trending Topics 18
- User Perspectives 65
- Video 59

## Comments

Thank you for this information and I really love the part of Big ban theory

Hi Valerio,

I am really interested in the example you posted because I want to simulate the non-newtonian fluid behaviour for Bingham fluid using the Bingham-Papanastasious model, but to compute the shear dependent viscosity for a given point I need to obtain the shear rate value at that point.

How have you computed the shear rate at point p1?

Considering that the model is two dimensional axisymmetric did you define the shear rate as du/dr, where u is the velocity profile and r is the radial coordinate?

Thank in advance for you reply

Hi Daniel,

Great questions! I’ll try to answer to all of them.

Q: I want to simulate the non-newtonian fluid behaviour for Bingham fluid using the Bingham-Papanastasious model, but to compute the shear dependent viscosity for a given point I need to obtain the shear rate value at that point.

A: All physics nodes in the model tree introduce predefined variables that can be usually used throughout the model. They’re typically functions of the dependent variables and their derivatives.

Display the Equation View subnode in the model tree to access them: click the Show button and select Equation View from the Model Builder. Click the Equation view subnode and the corresponding settings window will show you detailed information about the implementation of each physics feature, such as the variables.

Let’s take a look at the Fluid Properties node: it defines a variable that from its expression, description, and unit of measure, I’d say it’s exactly what you’re looking for. It’s the shear rate!

COMSOL allows you you to type in your user defined dynamic viscosity expression based on such variable (and others, if needed). In the Fluid-Structure Interaction in Aluminum Extrusion model available in the Model Libraries (http://www.comsol.com/model/fluid-structure-interaction-in-aluminum-extrusion-4386) we show how to do it.

Q: How have you computed the shear rate at point p1?

A: I’ve added this point to the geometry and once the model was solved, I’ve added to the Results branch a 1D Plot Group with a Point Graph.

Q: Considering that the model is two dimensional axisymmetric did you define the shear rate as du/dr, where u is the velocity profile and r is the radial coordinate?

A: Once you select the space dimension of your model, COMSOL will take care of the underlying mathematical formulation. You don’t have to worry about it but, if you’re really curious, you now know the trick: take a look under the hood with the Equation View subnode.

I hope you’ll find my answers useful.

Happy multiphysics simulation!

Valerio

P.S. Many of these variables are available in the Predefined quantities lists in the settings for plots and other results nodes.